Field Replacement Procedure

TSR® Series II Multi-service Connect (MSC) Module

06267-01 Rev. AB

---

This document provides instructions to install and configure the Multi-Service Connect (MSC) Module in the Terabit Switch Router Series II (TSR). Before beginning this procedure, carefully inspect the package to ensure no damage occurred during shipping or delivery. If you suspect any possible damage, contact Customer Service immediately.

For easy and quick reference, this Field Replacement Procedure (FRP) is organized as follows:

Support Services

Tools

Overview

Optical Interfaces

TSR II Module Population Rules

Preparing to Install Router Modules

Removing Router Module(s

Removing Filler Modules

Installing the MSC Module

Installing the Cable Management Bracket

Installing Fiber Optic Cables

Configuring the MSC Module

Support Services

To obtain information on customer service and training, contact Avici Customer Support:

• Phone:
  United States Support: 877-292-8424 (TSR-BY-AVICI)
  International Support: 01-978-964-2350
  
  
• E-mail: support@avici.com
  
  
• World Wide Web: http://www.avici.com
  
  

Tools

• 1/2 in flat blade screwdriver (filler modules)
  
  
• 3/8 in flat blade screwdriver (cable management bracket)
  
  
• 1/8 in flat blade screwdriver (SAM module)
  
  

Overview

The MSC module supports Asynchronous Transfer Mode (ATM) services. At present, there are three variations of the MSC module:

• 8-Port OC-12/STM-4
  
  
• 16-Port OC-3/STM-1
  
  
• 8-Port OC-3/STM-1|4-Port OC-12/STM-4
  
  

Labels on the MSC module faceplate identify the module type, the interface type, and the family type (see Figure 1). Labels on all MSC modules also indicate port numbers (see Figure 2).

In addition, faceplate LEDs indicate module, link, and activity status of the module and each of the ports. The Ethernet port connection on the faceplate allows the module to serve as a Server Attached Module (SAM).

NOTE The 8-Port OC-1, the 16-Port OC-3, and the 8-Port POC-3|4-Port OC-12 MSC modules are all Family 2 modules. Roman numerals on the faceplate label identify the module as a Family 2 module (see Figure 1).

Router modules must be installed in family pairs.That is, you must install two Family 1 or two Family 2 modules.

All MSC modules ship with a cable management bracket with Velcro fasteners on the cable management bracket for easy organization of fiber cables. In addition, the module ships with dust covers installed in each of the ports.

For instructional purposes, only images of the 8-Port OC-12 module are used throughout this document to demonstrate the installation procedures for MSC module types.

NOTE The cable management bracket is for cable management purposes only. You must remove the cable management bracket prior to removing the module.

As with all other router modules, proper installation procedure must be followed.

Figure 1. MSC Module Type Labels

Figure 2. MSC Module Port Numbering Labels

Optical Interfaces

All MSC modules support either Single Mode Intermediate Reach Telecordia GR-253 IR-1 compatible with S4.1 of ITU G.957 or multimode interfaces. Refer to Table 1.

Table 1. Optical Characteristics

Requirement	OC-12/STM-4	OC-12/MM	OC-3/STM-1	OC-3/MM
Wavelength range	1293-1334 nm	1270 - 1380 nm	1261-1360 nm	1270 - 1380 nm
Standard	IR-1	ATM	IR-1	ATM
Distance	15 km	300 m	15 km	2000 m
Receiver power	-28 to -8 dBm	-26 to -14 dBm	-28 to -8 dBm	-29 to -14 dBm
Transmit power	-15 to -8 dBm	-20 to -14 dBm	-15 to -8 dBm	-20 to -14 dBm
Attenuation range	0 to 12 dB	0 to 6 dB	0 to 12 dB	0 to 9 dB
Extinction ratio (min)	8.2 dB	10 dB	8.2 dB	10 dB

TSR II Module Population Rules

Each TSR II bay has four shelves numbered from 1 (top) to 4 (bottom). Each shelf has 11 slots to house the router and route controller modules. All router modules must be inserted in pairs. Route controllers are located on the right hand side of each bay shelf.

The location of the routing modules within the bay creates the TSR II system's "toroidal mesh." It is critical to install routing modules and route controller modules in predefined positions. All router modules must be inserted in family pairs.

Figure 3. TSR II Bay Shelf and Slot Numbering

Populating the Bay

The rules for populating the first TSR II Full Bay and TSR II Split Bay with router module pairs follow. See Figure 3 for TSR II bay slot number.

• Modules occupying a slot use the slot number as its identifier. A module is identified by bay number/slot number; i.e., 1/10 would be bay 1, slot 10.
  
  
• TSR II only accepts red modules. Module color is located at the top of the module and on the bottom of each slot (see Figure 4).
  
  

Figure 4. TSR II Red Module Identification

• The MSC module is a Family 2 module. Roman numerals on the faceplate label identify the module as a Family 2 module (see Figure 1).
  
  
• Router modules must be added in Family pairs. That is, you must install two Family 1 modules OR two Family 2 modules.
  
  
• If installing the module in a cold bay, follow the Population Rules outlined in the Terabit Switch Router Series II Install Guide.
  
  
• If installing the router module in a live bay use the show population CLI command - specifying the module family - to identify the slot(s) to populate.
  
  

Refer to IPriori CLI Configuration Guide (Vol. 1) and the CLI Reference Guides (Vol. 1) for further information on this command. Online versions of the manuals are available at http://www.avici.com/documentation.

Preparing to Install Router Modules

Before removing or installing modules, remove the EMI front cover (if installed) as outlined in the TSR II Install Guide.

Depending on the individual configuration of the TSR II, either a router module or a filler module must be removed in order to install the MSC module. Refer to "Removing Router Module(s)" to remove a router module. Refer to "Removing Filler Modules" to remove a filler module.

In order to prevent damage to the TSR II system from static electricity, use the following precautions:

• Do not handle modules unless you are using the appropriate antistatic protection, such as an antistatic wrist or heel strap and a properly grounded conductive mat.
  
  
• When using an antistatic wrist strap, attach the cord to the appropriate ground jack.
  
  
• Handle modules by outer enclosure only. Do not touch electrical connections, pins, or soldered surfaces.
  
  

CAUTION (1) When handling modules, wear a grounded wrist strap or equivalent antistatic protection to prevent damage to electronic parts.

Installing the Antistatic Wrist Strap

A grounded antistatic wrist strap must be used to protect the TSR II bay modules and components from damage caused by static.

PROCEDURE: Use the following procedure to install the antistatic wrist strap:

Step 1 Remove the alligator clip from the grounding pin on the antistatic wrist strap.

Step 2 Insert the grounding pin into the electrostatic discharge (ESD) jack on the front of the TSR II bay shelf (see Figure 5).

Step 3 Use the ESD wrist strap while handling modules.

Figure 5. TSR II ESD Jack Locations

Removing Router Module(s)

Before removing a module you must shut down the module being replaced. Use the shutdown command to disable all functions on the module. The module appears as administratively down when executing the show mod brief command.

Shutting Down the Module

To notify the system to shutdown a module, use the CLI command line to turn off the respective slot. Using the shutdown command allows the removal of the module without service interruption.

Example: Use the shutdown command to disable all functions on the module. The module appears as administratively down when executing the show mod brief command.

router(config)#module 1/25 router(config)#shutdown This command will disable module 1/25. Are you sure [yes|no}? yes Disabling module... router(config)#end router# router#show module brief Module Discovered Configured    Last Started                State   1/25     1xOC192c    1xOC192c     Never                  never    Admin Down   1/26     2x1GbE      2x1GbE       WEDS NOV 26 14:16:16:23 2003            Up . .   1/34      1x10GbE    1x10GbE      WEDS NOV 26 14:16:16:23 2003            Up   1/35      4xOC3c     4xOC3c       WEDS NOV 26 14:16:16:23 2003            Up  router#

When the module is shutdown, proceed with removing the router module.

Routine router module removal requires the disconnecting of existing fiber optic cable connections. Router modules serving as Server Attached Modules (SAMs) require disconnecting fiber optic and Ethernet cable connections to the server module.

CAUTION (2) Within five minutes of removal of a module, a replacement module or filler module must be installed in the empty slot to ensure proper air flow within the system.

PROCEDURE: Use the following steps to remove the router module(s):

Step 1 Verify that your antistatic wrist strap is properly grounded.

Step 2 Undress the fiber optic cable from the cable management bracket.

Step 3 Disconnect the LC fiber optic connectors from the module (see Figure 6). Carefully undress the cable and move it to the side to avoid damage.

WARNING (1) This is a Class 1 laser product. Invisible laser radiation can be emitted from the aperture of the port when the fiber cable is disconnected. Avoid exposure to laser radiation and do not look directly into open apertures. Replace dust caps into module ports after disconnecting fiber optic connectors.

Figure 6. Disconnecting LC Fiber Optic Connector

Step 4 Replace the dust cap(s) into each of the module ports after disconnecting fiber optic connectors.

Step 5 If this is SAM module, disconnect the Ethernet connector (see Figure 7). If it is not, proceed to Step 6. Hang the Ethernet cable down and out of the way, or tuck the cable into the horizontal cable tray under the module shelf.

Figure 7. Disconnecting Ethernet connector

Step 6 Using the 3/8 in flat-head screwdriver, unscrew the captive screws in the cable management bracket and remove the bracket from the module (see Figure 8).

Figure 8. Cable Management Bracket Removal

Step 7 Release the module from the backplane, simultaneously rotate the ejector latches to a fully open position and carefully pull the router a few inches out of the shelf (see Figure 9 and Figure 10).

Figure 9. Router Module Removal - 1

Step 8 To remove the module, grasp it on the top and bottom and pull it carefully out of the shelf.

CAUTION (3) When the ejector latch release lever is in the open position, do not use the latch lever to remove the module or adjust the module in the card guides. Failure to adhere to these guidelines may result in equipment damage.

Figure 10. Router Module Removal - 2

Step 9 Hold module in place with one hand at the bottom of case, then close the ejector latches by rotating them to the closed position and sliding the release levers in the direction of the arrows to lock the levers back into place (see Figure 11).

Figure 11. Router Module Removal - 3

Step 10 To remove the module, grasp it on the top and bottom and pull it carefully out of the shelf.

CAUTION (4) A detailed inspection of the Very High Density Metric (VHDM) connector is required each time a module is removed or inserted. Lay the module gently on its side to perform a VHDM connector inspection Any contact to a VHDM connector outside a TSR could damage the connector.

Step 11 Carefully inspect the VHDM connector for damage such as deformed sockets, holes between socket columns, and deformed guide fins on top and bottom of the socket columns (see Figure 12).

CAUTION (5) If the VHDM connector has any signs of damage, DO NOT insert it into an TSR. Mark the module and slot as damaged and call TSR-BY-AVICI to request an Return Material Authorization (RMA). DO NOT insert a new router module into the slot. If the slot is damaged, only insert filler modules. Contact Support Service immediately.

.

Figure 12. VHDM Connector

Step 12 Before placing the module in a static-proof bag, replace the VHDM (Very High Density Metric) protective cap over the VHDM connector at the rear of the module. This will protect the pins while the module is not in the TSR (see Figure 13).

CAUTION (6) If the empty slot is not populated with a module, it must be filled with a filler module within five minutes.

Step 13 Repackage according to RMA directions. Ship back to Avici.

Figure 13. Replacing the VHDM Protective Cap

Removing Filler Modules

The TSR systems ships with 18 filler modules, which ensures proper cooling and elimination of electromagnetic interference during operation. Remove filler modules from slots intended for router modules (see Figure 14).

Figure 14. Filler Module

If you are removing a filler module from the TSR, use the following procedure.

PROCEDURE: Use the following steps to remove a filler module:

Step 1 Use a 1/2-in. flat-blade screw driver to loosen the lock latch on the filler module.

Step 2 Pull the filler module out of the slot (see Figure 15).

Step 3 Store the filler module in a dry, cool area.

Figure 15. Removing Filler Modules

Installing the MSC Module

Install the MSC module after removing either a router of filler module. Refer to "TSR II Module Population Rules" .

NOTE When the ejector latch release lever is in the open position, do not use the lever to lift or adjust the module in the card guide (see Figure 18).

For instructional purposes, only images of the 8-Port OC-12 MSC module are used throughout this document to demonstrate the installation procedures for MSC module types.

PROCEDURE: Use the following steps to install the MSC modules:

Step 1 Verify that your antistatic wrist strap is properly grounded.

NOTE Router modules must be added in Family pairs. That is, you must install two Family 1 modules OR two Family 2 modules.

Step 2 Remove the MSC Module from its static protection packaging. Ensure that this is a module with a red dot.

NOTE The TSR II only accepts red modules.

Step 3 Before inserting the module, remove the VHDM protective cap from the end of the module before use. Set the protective cap aside in a safe place (see Figure 16).

Figure 16. Remove VHDM Protective Cap Before Use

CAUTION (7) A detailed inspection of the VHDM connector is required prior to insertion. Lay the module gently on its side so you can perform a VHDM connector inspection. If the VHDM connector shows any signs of damage, DO NOT insert it into a chassis. Mark the module as damaged and call TSR-BY-AVICI to request an RMA.

Step 4 Carefully inspect the VHDM connector for damage such as deformed sockets, holes between socket columns, and deformed guide fins on top and bottom of the socket columns (see Figure 17).

.

Figure 17. VHDM Connector

NOTE If the VHDM connector has any signs of damage, DO NOT insert it into a TSR. Mark the module as damaged and call TSR-BY-AVICI to request an RMA.

Step 5 If there are modules with cable tray faceplates, ensure that the cable trays on the adjacent router modules in the chassis are fully closed.

Step 6 Ensure that all chassis cabling is clear for module insertion.

Step 7 Close the ejectors latches completely by sliding the release levers in the direction of the arrows and locking into place (see Figure 18).

Figure 18. Router Module Installation -1

Step 8 Align the module with the card guides and slide the module into the slot until the ejector latch's release lever tab hits the outer lip of the shelf (see Figure 19 and Figure 20).

Figure 19. Router Module Installation - 2

Step 9 Simultaneously slide the release levers in the direction of the arrows and rotate the ejector latches to the open position (see Figure 20 and Figure 21).

CAUTION (8) When the ejector latch is in the open position, do not use the lever to lift or adjust the module in the card guide. Failure to adhere to these guidelines may result in equipment damage.

Figure 20. Router Module Installation - 3

Figure 21. Router Module Insertion - 4

Step 10 Slide the module in until the ejector latch tab slides into position behind the outer lip of the shelf (see Figure 22).

NOTE Do not push the module too far into the slot. The ejector latch tabs must not extend beyond the groove that forms the outer lip of the shelf.

Figure 22. Router Module Insertion - 5

Step 11 Simultaneously depress the release levers on the top and bottom ejector latches and rotate the ejector latch to the closed position (see Figure 22 and Figure 23). Release the release levers once the ejector latches are closed.

NOTE If the ejector latches will not close, reseat the module by pulling it six inches out of the slot and then repeating Step 8 through Step 12, making sure the module is not inserted too far into the slot. If the ejector latches still do not close after reseating the module, contact Avici Customer Support.

Figure 23. Router Module Insertion - 6

LEDs

The MSC module supports LEDs on the faceplate to indicate the status of the module and the link and activity status of each of the ports (see Figure 24).

Board Status

The two top LEDs indicate "up" status of the board. During routing module POST, the red triangle shaped LED on the faceplate lights and remains lit until POST is completed. After completion of POST, the green square LED lights and blinks and the red LED is extinguished. The green LED remains in the blinking state until the module is enabled, at which time the LED transitions to solid.

The solid green LED indicates that the module has passed POST.

If the red LED remains lit, POST has detected a nonrecoverable error or fault. If the red LED remains lit, remove and reseat the module to run POST again.

Port Status

The eight (two per port) bottom bi-color LEDs, indicate port status. These bottom LEDs consist of two pairs of LEDs: the left most LED (green or not lit) indicates port status and the right most LED (amber or not lit) indicates activity status, one set per port.

The right LED (A) indicates activity of the port. The right LED blinks amber when the link is actively passing traffic.

Figure 24. MSC Module LEDs

Installing the Cable Management Bracket

After installing the module, install the cable management bracket. Receptive screw holes in the module faceplate accept the captive screws of the cable management bracket. Velcro fasteners in the cable management bracket allow easy dressing and organization of fiber optic cables.

NOTE The cable management bracket is intended for cable management purposes only. The cable management bracket must be removed prior to removing the module.

Figure 25. Cable Management Bracket Installation

PROCEDURE: Use the following procedure to install the cable management bracket to the module:

Step 1 Remove the cable management bracket from its package.

Step 2 Position the cable management bracket as shown in Figure 25.

Step 3 Using a 3/8 in flat-head screwdriver, attach the bracket to the module faceplate by tightening the captive screws (see Figure 25).

CAUTION (9) The cable management bracket is for cable management purposes only. The cable management bracket must be removed prior to removing the MSC module. DO NOT use the cable management bracket to lift or carry the MSC module. Failure to adhere to these guidelines may result in equipment damage.

Installing Fiber Optic Cables

The installation of fiber optic cables in the MSC module follows the usual procedure for fiber optic installation. If connecting all 4 ports, remove the dust cap and install the fiber optic cables in one port at a time. Dust caps should only be removed immediately prior to fiber optic cable installation. Clean all fiber optic connectors according to manufacturer's instructions.

CAUTION (10) Fiber optic cables must be thoroughly cleaned each time a cable is connected or reconnected. Failure to do so may impact performance to the fiber optic cable Dust caps should only be removed immediately prior to fiber optic cable installation.

PROCEDURE: Use the following steps to install the fiber optic cables in the MSC module:

Step 1 Verify that your antistatic wrist strap is properly grounded.

WARNING (2) This is a Class 1 laser product. Invisible laser radiation can be emitted from the aperture of the port when the fiber cable is disconnected. Avoid exposure to laser radiation and do not look directly into open apertures.

Step 2 Remove the dust cap from the port slot where installing the fiber optic cable (see Figure 26).

Figure 26. Removal of Dust Cap

Step 3 Remove cap from fiber optic cable connector and insert LC connector into the port slot (see Figure 27).

Figure 27. Installation of Fiber Optic Connector/Cable

NOTE If installing fiber optic cables into all 8ports at once, begin at the bottom port and move upward to for ease of fiber management.

Step 4 Repeat Step 2 and Step 3 for each fiber optic connection.

Step 5 Use the Velcro fasteners on the cable management bracket to dress the fiber optic cables (see Figure 28).

Figure 28. Dressing of Fiber Optic Cables

NOTE If this is a Server Attached Module (SAM) proceed with Step 6. If this is not a SAM, disregard Step 6 and Step 7.

Step 6 Position the Ethernet adapter cable on the Ethernet connector on the module as shown in Figure 29.

Step 7 Using a 1/8 in flat head screwdriver, tighten the two screws to secure the Ethernet adapter cable to the Ethernet port on the module (see Figure 29).

Figure 29. Server Attached Module (SAM) Installation

Configuring the MSC Module

To configure the MSC module, activate the installed module as described in the following sections.

Activating a MSC Module

PROCEDURE: Use the following steps to configure and activate a module.

Step 1 Use the module command to identify the module to be activated. Module type is auto detected.

Step 2 Use the no shutdown command to activate the module.

Example: In the following example:

• The module command assigns a MSC module to bay 1, slot 35.
  
  
• The no shutdown command enables the module.
  
  
• The show modules command displays the new configuration:
  
  

router#configure terminal Enter configuration commands, one per line. End with CNTL/Z. router(config)#module 1/35 router(config-module)#no shutdown router(config-module)#end router#show modules

MODULE 1/35   Discovered (8xOC12ms) 8 Port Channelized POS/ATM OC-12c/STM-4c MPLS-Capable Configured (8xOC12ms) 8 Port Channelized POS/ATM OC-12c/STM-4c Physical port type is unknown Hardware is 8xOC12ms, Version version number.number, Revision revision number   Fabric version is version number   IPriori Bootrom Release release number   Operational image version: Platform: platform; Label: release label Built on build date, build time ROM Version: IPriori Bootrom Release number.number, build month, day, year Line Card #1      Line Card FPGA Software Version: FPGA version number Line Card #2      Line Card FPGA Software Version: FPGA version number      Switch Card FPGA Software Version: FPGA version number POST Software Version: version number Product Id: P4-S16O48-SR-R (Rev. AX); S/N serial number Module CLEI Code: CLEI code number Last started on DAy Date Time Year Module uptime is Weeks, Days, Hours, Minutes, Seconds Administratively Up; Current state is Up Max number of historical logging files: 5 router#

The module Command

The module command is used to enter module mode.

Syntax: [no] module bay#/slot# [type]

bay#	Defines the bay number in which this module is located. Value is 1 to 4.
slot#	Defines the slot number to configure. Slots are numbered from 1 to 10 beginning at the left of the machine. Each physical slot is numbered on the hardware for reference.
type	The type of module to configure in this slot. When configuring a MSC module: 8xOC12ms - Assign a MSC module to the slot

Description: Within module mode, the following commands are available:

Table 2. Module Mode Command

Command	Description
auto-upgrade	Enable Auto Upgrade of images for the module.
boot [flags flag {1|2} | file | package-file]	Modify boot parameters for this module. Specify an image file or package file to be used at the next module start.
default	Sets module to default settings.
do	Allow invoking of executive-mode commands from within any configuration-mode.
exit	Exit from module mode
fabric link down-event	Configure the amount of down events allowed for this link.
fabric link time-window	Configure the time window to allow the down events to occur in.
fpga activebank	Sets the memory bank from which the FPGA is loaded during the next module boot/reboot.
fpga download	Download an FPGA image to the modules from a file or package file.
help	Description of the interactive help system
ip	Configure NetFlow parameters used for exporting IP flow statistics for the module. The command overrides the NetFlow parameters set globally.
logging-filter system level	Specify that the hardware entity does not generate events for the specified system at or below the specified level. Note that critical errors are always generated regardless of filtering. Multiple logging filter statements can be given. Default is to log all levels including and above warning for all systems.
logging-max-history max_files	Change the maximum number of log files that are created on the permanent storage for the current system. A number will form the extension to the stored file name and be numbered from 0 to max_file -1. Default is 5. Allowed range is 1 to 100.
post-burn [filename | package-file]	Burn a POST image from a file or package file onto a specified module or all modules.
reboot [filename | package-file][1 | 2]	Specify the file or package file, and the memory bank to be used when the system starts and restart the system.
rom-burn filename	Burn a boot ROM image from a file or package file onto a specified module or all modules.
run	Allow invoking of executive-mode commands from within any configuration-mode.
shutdown	Disable/enable a module (or module subsystem).

The primary function available in module mode is the ability to configure or delete the module that resides in the slot. This is done with the [no] shutdown command. The shutdown command disables and shuts down the module residing in the slot. The no shutdown command enables or configures the module residing in the slot.

Use the no module [bay/slot] command to delete a module.

Related Commands: show modules

Display the Modules

Use the show modules command to display the current configuration and state for a module.

Syntax: show modules [bay/slot] [brief]

bay/slot	Show only information for the module residing in bay/slot where bay is the bay number and slot is the slot number.
brief	Display summarized information about the specified module(s).

Description: This command displays configuration information for one or all modules residing in this bay.

The show modules brief command will display which module is the SAM module by starting the information line with an S in the case of the primary SAM and a B in the case of a backup SAM.

Default: None.

Command Mode: Privileged.

Example 1: In the following example, the show modules command displays information about all the configured modules:

MODULE 1/35:   Discovered (8xOC12ms) 8 Port Channelized POS/ATM OC-12c/STM-4c MPLS-Capable Configured (8xOC12ms) 8 Port Channelized POS/ATM OC-12c/STM-4c Physical port type is unknown   Hardware is 8xOC12ms, Version version number.number, Revision revision number   Fabric version is version number   IPriori Release version release number   Operational image version: Platform: platform; Label: release label Built on build date, build time ROM Version: IPriori Bootrom Release number.number, build month, day, year   Line Card #1      Line Card FPGA Software Version: FPGA version number   Line Card #2      Line Card FPGA Software Version: FPGA version number      Switch Card FPGA Software Version: FPGA version number POST Software Version: version number Product Id: Product Identification Number; S/N serial number Module CLEI Code: CLEI code number Last started on Day Date Time Year Module uptime is Weeks, Days, Hours, Minutes, Seconds Administratively Up; Current state is Up Max number of historical logging files: 5 router#

The following table describes the fields in the display:

Table 3. Fields Displayed by show modules 

Field	Description
MODULE n/n	Specifies the bay number and slot number.
Server Access Module/Backup Server Access Module	This line appears if the specified module is a server attached module or backup server access module.
Discovered	Specifies the type of module discovered by the Bay Controller in the specified slot. Indicates if this module is capable of supporting MPLS.
Configured	Specifies they type of module configured for this slot.
Physical port type	Specifies the type of fiber installed in the specified slot.
Hardware is	Hardware type and version number for the module.
Fabric version	Version of the Avici router fabric.
IPriori release version:	Version of IPriori software loaded on the module.
Operational image version	Platform, label and date operational image was built.
ROM version:	Version of the Boot ROM on the module.
Line Card #1 - FPGA Software Version	Version of the FPGA software on the line card portion of the module.
Line Card #2 - FPGA Software Version	Version of the FPGA software on the line card portion of the module.
Switch Card FPGA Software Version	Version of the FPGA software on the line card portion of the module. Displayed only if the switch card has an FPGA.
POST Software Version	Version of the POST image on the module.
Product Id:	Specifies the product identifier for the module.
Module CLEI Code:	Common Language Equipment Identification (CLEI) Code assigned by Telcordia for this module.
Last started on	The time at which the module was last started.
Module Uptime	The amount of time the module has been up.
Administrative status	Indicates the administrative state of the module. Administratively Up - Module has been discovered and configured and is operational. Administratively Down - module is discovered and configured but has been shut down.
Current state is	Indicates the operational state of the module. up - Module has been discovered and configured and is operational. down - module is discovered and configured but is not operating. Indicates problem. unconfigured - Module has been booted but has not yet been fully configured. misconfigured - Module has been booted but is not properly configured. unknown - The bay controller has not yet discovered the module. IncompatibleSW - The module is running a software image that is not compatible with the server(s), bay controllers, and other modules.
Max number of historical logging files:	A value from 1 to 199, indicating the maximum number of log files created. Set using the logging-max-history command.
Non-default logging filters:	Input filtering to the logging system as defined using the logging-filter command.

Example 2: In the following example, the show modules brief command displays summarized information about the modules:

router#show module brief Module Discovered Configured      Last Started            State __1/5      8xOC12      8xOC12         WED Jan 12 22:16:14 2004            Up   1/15     16xOC3ms    16OC3ms        WED JAN 14 22:33:24 2004            Up   1/16     2x1GbE      2x1GbE         WED NOV 26 14:16:16 2003            Up . .   1/24      1x10GbE    1x10GbE        WED NOV 26 14:16:16 2003            Up   1/25      4xOC3c     4xOC3c         WED NOV 26 14:16:16 2003            Up   1/35     8xOC12ms    8xOC12ms      WED JAN 14 22:33:15 2004            Up  router#

The following table describes the fields in the display:

Table 4. Fields Displayed by show modules brief                     

Field	Description
Module (x/x)	Bay and slot number where the module is installed.
Discovered	Indicates the type of module and the number of ports on the module as discovered by the bay controller.
Configured	Indicates the type of module IPriori has configured for the specified bay/slot.
Last Started	Date and time of last start.
Status	Admin Up - Module has been discovered and configured and is operational. Admin Down - module is discovered and configured but has been shut down Up - Module has been discovered and configured and is operational. Down - module is discovered and configured but is not operating. Indicates problem. Unconfigured - Module has been booted but has not yet been fully configured. Misconfigured - Module has been booted but is not properly configured. Unknown - The Bay Controller has not yet discovered the module. IncompatibleSW - The module is running a software image that is not compatible with the server(s), bay controllers, and other modules.

Refer to IPriori CLI Reference and Configuration Guides (Vols.1 & 2) for further information on configuring the MSC module. An online version of the manuals is available at http://www.avici.com/documentation.

Copyright © 2005 Avici Systems Inc.
Avici® and TSR® is a registered trademark of Avici Systems Inc.
IPriori™, Composite Links™, SSR™, QSR, and NSR® are trademarks of Avici Systems Inc.

   Source File Name: 06267-01%20revAB.fm
    HTML File Name: 06267-01%20revAB.html
    Last Updated: 07/28/05 at 15:47:20

Please email suggestions and comments to: doc@avici.com