This document provides instructions to install and configure the 1-Port OC-192c module in the Quarter-rack Scalable Router (QSR) Before beginning this procedure, carefully inspect the package to ensure no damage occurred during shipping or delivery. If you suspect any possible damage, contact Customer Service immediately.
For easy and quick reference, this Field Replacement Procedure (FRP) is organized as follows:
Support Services Tools Overview Optical Interfaces QSR Module Population Rules Preparing to Install Router Modules Removing Router Module(s) Removing Filler Modules Removing Fabric Filler Modules Installing the 1-Port OC-192c Module Installing the Cable Management Bracket Installing Fiber Optic Cables Configuring the 1-Port OC-192c Router Module Configuring the Interfaces Support Services
To obtain information on customer service and training, contact Avici Customer Support:
- Phone: United States Support: 877-292-8424 (TSR-BY-AVICI)
International Support: 01-978-964-2350
- E-mail: support@avici.com
- World Wide Web: http://www.avici.com
Tools
- 1/2 in. flat blade screwdriver (if removing filler modules)
- 3/8 in. flat blade screwdriver (if installing a SAM module)
- 1/8 in flat blade screwdriver (SAM module)
Overview
The 1-Port OC-192c is a 10Gbit/s, single-slot module supports PPP and Multi-Protocol Label Switching (MPLS) over SONET/SDH. Faceplate LEDs indicate module, link, and activity status (see Figure 1). The Ethernet port connection on the faceplate allows the module to serve as a Server Attached Module (SAM).
NOTE The 1-Port OC-192c is a Family 2 module. Roman numerals on the faceplate label identify the module as a Family 2 module (see Figure 1).
The 1-Port OC-192c module ships with a cable management bracket. Velcro fasteners on the cable management bracket allows for ease of dressing and organization of fiber cables. In addition, the 1-Port module ships with an Electro Magnetic Interference (EMI) dust cover installed in the port.
NOTE The cable management bracket is intended for cable management purposes only. The cable management bracket must be removed prior to removing the module.
As with all other router modules, proper installation procedure must be followed.
Figure 1. 1-Port OC-192c Module Faceplate
Optical Interfaces
This Single-Port OC-192c module supports Telcordia Single Mode Short Reach SR-1 compliant optics as described in GR-1377-CORE, compatible with SR-1 of GR-253 and I-64.1 of ITU G.691. Also supported are Single Mode Intermediate Reach interfaces compatible with Telecordia GR-253 IR-2 and ITU G.691 S-64-2b and SM LR interfaces compatible with Telecordia GR-253 LR-2 and ITU G.691 L-64-2. Refer to Table 1.
QSR Module Population Rules
Each QSR chassis provides a single chassis with 10 slots to house route controller and router modules. The chassis accepts one or two route controller modules and up to eight router modules. Route controller modules can only reside in slots 10 and 1 (S10 and S1). If populating a QSR chassis with only one route controller module, the route controller must be installed in S10.
Figure 2 shows QSR chassis slot numbering when viewed from the front of the QSR.
The software command show population designates router module population sequence. Use this CLI command to determine where to install the router module in the chassis.
Figure 2. QSR Chassis Slot Numbering
Rules for populating a single QSR chassis are as follows:
- Install route controller modules in slots S10 and S1. The QSR accepts only NSR® Route Controller Modules.
- When only one route controller module is installed, install it in slot S10. Use slot S1 for a router, a filler module, or a fabric filler module.
- A module occupying a slot uses the slot number as its identifier.
- Initial installation of two router modules is required in the first QSR chassis only. Modules may then be added one at a time.
- Every router module must be abutted by another router module, a route controller module, or a fabric filler module.
NOTE Remember, if installing modules in slots 5 and 6 only, slots 4 and 7 must contain a fabric filler module. The remaining empty slots must contain standard filler modules.
For example, you plan to use only two router modules in the chassis and you install them in slots 5 and 6. Slots 4 and 7 must contain a fabric filler module.
The remaining empty slots must contain standard filler modules.
Or, your QSR contains a single route controller module in slot S10 and eight router modules in slots 2 through 8. Slot S1 must contain a fabric filler module. Fabric filler modules ensure multiple communications routes between installed modules.
NOTE Fabric filler modules differ from standard filler modules.
- Add a standard filler module to any empty slot in the chassis. During QSR operation, standard filler modules ensure proper cooling and eliminate electromagnetic interference.
- If installing the module in a cold chassis, follow the Population Rules outlined in the Quarter-rack Scaleable Router Install Guide.
- The 1-Port OC-192c is a Family 2 module. Roman numerals on the faceplate label identify the module as a Family 2 module (see Figure 1).
- If installing the router module in a live chassis use the show population CLI command - specifying the module family - to identify the slot to populate.
Refer to IPriori CLI Reference and Configuration Guides (Vol. 1) for further information on this command. Online versions of the manuals are available at http://www.avici.com/documentation.
Preparing to Install Router Modules
Depending on the individual configuration of the QSR, either a router module, a filler module, or a fabric filler module must be removed in order to install the 1-Port OC-192c module. Refer to "Removing Router Module(s)" to remove a router module, "Removing Filler Modules" to remove a filler module, and "Removing Fabric Filler Modules" to remove a fabric filler module.
In order to prevent damage to the QSR system from static electricity, use the following precautions:
- Do not handle modules unless you are using the appropriate antistatic protection, such as an antistatic wrist or heel strap and a conductive mat.
- When using an antistatic wrist strap, attach the cord to the appropriate ground jack.
- Handle modules by outer enclosure only. Do not touch electrical connections, pins, or soldered surfaces.
CAUTION (1) When handling router modules, wear a grounded wrist strap or equivalent antistatic protection to prevent damage to electronic parts.
Installing the Antistatic Wrist Strap
A grounded antistatic wrist strap must be used to protect the QSR chassis modules and components from damage caused by static.
PROCEDURE: Use the following procedure to install the antistatic wrist strap:
Step 1 Remove the alligator clip from the grounding pin on the antistatic wrist strap.
Step 2 Insert the grounding pin into the electrostatic discharge (ESD) jack on the front of the QSR chassis shelf (see Figure 3).
Step 3 Use the ESD jack while handling modules.
Figure 3. QSR ESD Jack Location (Front)
Removing Router Module(s)
Before removing a module you must shut down the module being replaced. Use the shutdown command to disable all functions on the module. The module appears as administratively down when executing the show mod brief command.
Shutting Down the Module
To notify the system to shutdown a module, use the CLI command line to turn off the respective slot. Using the shutdown command allows the removal of the module without service interruption. Before removing a module you must shut down the module being replaced.
Example: Use the shutdown command to disable all functions on the module. The module appears as administratively down when executing the show mod brief command.
router(config)#module 1/4/1
router(config-if)#shutdown
router(config-if)#end
router#
router#show module brief
Module Discovered Configured Last Started State
1/1 1xOC192c 1xOC192c MON DEC 17 10:40:07 2003 Up
1/2 2x1GBE 2x1GbE MON SEP 2 10:40:07 2002 Up
.
.
1/4 1xOC48c 1xOC48c MON SEP 2 10:40:08 2002 Down
1/5 4xOC3c 4xOC3c MON SEP 2 10:40:07 2002 Up
1/6 1xOC12c 1xOC12c MON SEP 2 10:39:57 2002 Up
1/3 4xOC12c 4xOC12c MON SEP 2 10:40:07 2002 Up
router#
When the module is shutdown, proceed with removing the router module.
Routine router module removal requires the disconnecting of existing fiber optic cable connections. Router modules serving as Server Attached Modules (SAMs) require disconnecting fiber optic and Ethernet cable connections to the server module.
WARNING (1) This is a Class 1 laser product. Invisible laser radiation can be emitted from the aperture of the port when the fiber cable is disconnected. Avoid exposure to laser radiation and do not look directly into open apertures.
PROCEDURE: Use the following steps to remove the router module(s):
Step 1 Verify that your antistatic wrist strap is properly grounded.
Step 2 Undress the fiber optic cable from the cable management bracket.
Step 3 Disconnect the SC fiber optic connectors from the module (see Figure 4). Carefully undress the cable and move it to the side to avoid damage.
Figure 4. Disconnecting SC Fiber Optic Connector
Step 4 If it is not a SAM module, proceed to Step 5. If this is SAM module, disconnect the Ethernet connector (see Figure 5).Hang the Ethernet cable down and out of the way, or tuck the cable into the horizontal cable tray under the module shelf.
Figure 5. Router Module Faceplate
Step 5 Using the 3/8 in flat-head screwdriver, unscrew the captive screws in the cable management bracket and remove the bracket from the module (see Figure 6).
Figure 6. Cable Management Bracket Removal
Step 6 Release the module from the backplane, simultaneously rotate the ejector latches to a fully open position and carefully pull the router a few inches out of the shelf (see Figure 7 and Figure 8).
Figure 7. Router Module Removal - 1
Step 7 To remove the module, grasp it on the top and bottom and pull it carefully out of the shelf.
CAUTION (2) When the ejector latch release lever is in the open position, do not use the latch lever to remove the module or adjust the module in the card guides. Failure to adhere to these guidelines may result in equipment damage.
Figure 8. Router Module Removal - 2
Step 8 Hold module in place with one hand at the bottom of case, then close the ejector latches by rotating them to the closed position and sliding the release levers in the direction of the arrows to lock the levers back into place (see Figure 9).
Figure 9. Router Module Removal - 3
Step 9 To remove the module, grasp it on the top and bottom and pull it carefully out of the shelf.
- A detailed inspection of the Very High Density Metric (VHDM) connector is required each time a module is removed or inserted. Lay the module gently on its side to perform a VHDM connector inspection.
CAUTION (3) Any contact to a VHDM connector outside a QSR could damage the connector.
Step 10 Carefully inspect the VHDM connector for damage such as deformed sockets, holes between socket columns, and deformed guide fins on top and bottom of the socket columns (see Figure 10).
NOTE If the VHDM connector has any signs of damage, mark the module and slot as damaged and call TSR-BY-AVICI to request an Return Material Authorization (RMA). DO NOT insert a new fabric filler or router module into the slot. If the slot is damaged, only insert filler modules. Contact Support Services immediately.
Figure 10. VHDM Connector
.
Step 11 Before placing the module in a static-proof bag, replace the VHDM High protective cap over the VHDM connector at the rear of the module. This will protect the pins while the module is not in the QSR (see Figure 15). If this is an RMA, repackage according to RMA directions. Ship back to Avici.
CAUTION (4) If the empty slot is not populated with a module, it must be filled with a filler or a fabric filler module within five minutes.
Removing Filler Modules
The QSR systems ships with 5 filler modules, which ensures proper cooling and elimination of electromagnetic interference during operation. Remove filler modules from slots intended for router modules (see Figure 11).
Figure 11. Filler Module
If you are removing a filler module from the QSR, use the following procedure.
PROCEDURE: Use the following steps to remove a filler module:
Step 1 Use a 1/2 in. flat-blade screw driver to loosen the lock latch on the filler module.
Step 2 Pull the filler module out of the slot (see Figure 12).
Step 3 Store the filler module in a dry, cool area.
Figure 12. Removing Filler Modules
Removing Fabric Filler Modules
The QSR systems ships with two (2) fabric filler modules that ensure a robust and reliable topology between modules. Remove fabric filler modules from slots intended for router modules.
To avoid damage to the backplane, perform a detailed inspection of the fabric filler module VHDM connector each time you remove or insert a module.
PROCEDURE: Use the following procedure to remove a fabric filler module:
Step 1 Verify that the wrist strap you are wearing is properly grounded or that other antistatic measures are in place.
Step 2 To unlock the ejector latches on the module, simultaneously do the following to both latches (see Figure 13):
- Press release levers in the directions indicated by the arrows on the latch.
- Rotate the ejector latches away from the module faceplate.
Figure 13. Opening Fabric Filler Module Latches
Step 3 Pull the module out of the chassis to unseat the backplane connectors.
Step 4 Carefully inspect the Very High Density Metric (VHDM) connector for damage such as deformed sockets, holes between socket columns, or distorted guide fins on the top and bottom of the socket columns (see Figure 14).
Figure 14. Fabric Filler Module VHDM Connector
.
CAUTION (5) If the VHDM connector shows any signs of damage, mark the module and slot as damaged and call TSR-BY-AVICI to request an Return Material Authorization (RMA).
DO NOT insert a new fabric filler or router module into the slot. If the slot is damaged, only insert filler modules. Contact Support Services immediately.
Installing the 1-Port OC-192c Module
Install the 1-Port OC-192c module after removing either a router of filler module. Refer to "QSR Module Population Rules" .
NOTE When the ejector latch release lever is in the open position, do not use the lever to lift or adjust the module in the card guide (see Figure 17).
PROCEDURE: Use the following steps to install the 1-Port OC-192c modules:
Step 1 Verify that your antistatic wrist strap is properly grounded.
Step 2 Remove the 1-Port OC-192c from its static protection packaging.
Step 3 Before inserting the module, remove the VHDM protective cap from the end of the module before use. Set the protective cap aside in a safe place (see Figure 15).
NOTE The QSR chassis accepts only red modules. The module color is located at the top side of the module.
Figure 15. Remove VHDM Protective Cap Before Use
NOTE A detailed inspection of the VHDM connector is required prior to insertion. Lay the module gently on its side so you can perform a VHDM connector inspection.
Step 4 Carefully inspect the VHDM connector for damage such as deformed sockets, holes between socket columns, and deformed guide fins on top and bottom of the socket columns (see Figure 16).
Figure 16. VHDM Connector
.
NOTE If the VHDM connector has any signs of damage, DO NOT insert it into a QSR. Mark the module as damaged and call TSR-BY-AVICI to request an RMA.
Step 5 If there are modules with cable tray faceplates, ensure that the cable trays on the adjacent router modules in the chassis are fully closed.
Step 6 Ensure that all chassis cabling is clear for module insertion.
Step 7 Close the ejectors latches completely by sliding the release levers in the direction of the arrows and locking into place (see Figure 17).
Figure 17. Router Module Installation -1
Step 8 Align the module with the card guides and slide the module into the slot until the ejector latch's release lever tab hits the outer lip of the shelf (see Figure 18 and Figure 19).
Figure 18. Router Module Installation - 2
CAUTION (6) When the ejector latch is in the open position, do not use the lever to lift or adjust the module in the card guide. Failure to adhere to these guidelines may result in equipment damage.
Step 9 Simultaneously slide the release levers in the direction of the arrows and rotate the ejector latches to the open position (see Figure 19 and Figure 20).
Figure 19. Router Module Installation - 3
Figure 20. Router Module Installation - 4
Step 10 Slide the module in until the ejector latch tab slides into position behind the outer lip of the shelf (see Figure 21).
NOTE Do not push the module too far into the slot. The ejector latch tabs must not extend beyond the groove that forms the outer lip of the shelf.
Figure 21. Router Module Installation - 5
Step 11 Simultaneously depress the release levers on the top and bottom ejector latches and rotate the ejector latch to the closed position (see Figure 21 and Figure 22). Release the release levers once the ejector latches are closed.
NOTE If the ejector latches will not close, reseat the module by pulling it six inches out of the slot and then repeating Step 7 through Step 11, making sure the module is not inserted too far into the slot. If the ejector latches still do not close after reseating the module, contact Avici Customer Support.
Figure 22. Router Module Installation - 6
LEDs
LEDs on the faceplate of the 1-Port OC-192c module indicate the status of the module and the link and activity status of each of the ports (see Figure 23).
Board Status
The two top LEDs indicate "up" status of the board. During routing module POST, the red triangle shaped LED on the faceplate lights and remains lit until POST is completed. After completion of POST, the green square LED remains solid and the red LED is extinguished.
The solid green LED indicates that the module has passed POST.
If the red LED remains lit, POST has detected a nonrecoverable error or fault. If the red LED remains lit, remove and reseat the module to run POST again.
Port Status
The two port LEDs indicate port status. These LEDs consist of two LEDs: the left most LED (green, not lit) indicates port status and the right most LED (amber, not lit) indicates activity status, one set per port.
When the link is up, the left most LED (L) will be solid green. If no light is present, the port is down. The right LED (A) indicates activity of the port. The right LED blinks amber when the link is actively passing traffic.
Figure 23. 1-Port OC-192c Module LEDs
Installing the Cable Management Bracket
After module installation, install the cable management bracket. Receptive screw holes in the module faceplate accept the captive screws of the cable management bracket. Velcro fasteners in the cable management bracket allow easy dressing and organization of fiber optic cables.
CAUTION (7) The cable management bracket is for cable management purposes only. The cable management bracket must be removed prior to removing the 8-Port module. DO NOT use the cable management bracket to lift or carry the 1-Port OC-192c module. Failure to adhere to these guidelines may result in equipment damage.
Figure 24. Cable Management Bracket Installation
PROCEDURE: Use the following procedure to install the cable management bracket to the module:
Step 1 Remove the cable management bracket from its package.
Step 2 Position the cable management bracket as shown in Figure 24.
Step 3 Using a 3/8 in flat-head screwdriver, attach the bracket to the module faceplate by tightening the captive screws (see Figure 24).
Installing Fiber Optic Cables
The installation of fiber optic cables in the 1-Port OC-192c module follows the usual procedure for fiber optic installation. If connecting all 4 ports, remove the dust cap and install the fiber optic cables in one port at a time. Dust caps should only be removed immediately prior to fiber optic cable installation. Clean all fiber optic connectors according to manufacturer's instructions.
CAUTION (8) Fiber optic cables must be thoroughly cleaned each time a cable is connected or reconnected. Failure to do so may impact performance or damage to the fiber optic cable.
WARNING (2) This is a Class 1 laser product. Invisible laser radiation can be emitted from the aperture of the port when the fiber cable is disconnected. Avoid exposure to laser radiation and do not look directly into open apertures.
PROCEDURE: Use the following steps to install the fiber optic cables in the 1-Port OC-192c module:
Step 1 Remove the dust cap from the port slot where installing the fiber optic cable (see Figure 25).
Figure 25. Removal of Dust Cap
Step 2 Remove cap from fiber optic cable connector and insert SC connector into the port slot (see Figure 26).
Figure 26. Installation of Fiber Optic Connector/Cable
Step 3 Use the velcro fasteners on the cable management bracket to dress the fiber optic cables (see Figure 27).
Figure 27. Dressing of Fiber Optic Cables
Step 4 If this is not a SAM module, proceed to Step 5. If this is a SAM module, position the Ethernet dongle cable on the Ethernet connector on the module as shown in Figure 28.
Step 5 Using a 1/8 in. flat-head screwdriver, tighten the two screws to secure the Ethernet cable to the Ethernet port on the module (see Figure 28).
Figure 28. Server Attached Module (SAM) Installation
Configuring the 1-Port OC-192c Router Module
To configure the 1-Port OC-192c module, activate the installed module and configure the interface as described in the following sections.
NOTE This section provides the information required to boot the module and configure the interface for PPP.
Activating a 1-Port OC-192c Module
PROCEDURE: Use the following steps to configure and activate a module.
Step 1 Use the no shutdown command to activate the module.
Example: In the following example:
- The module command assigns a 1-Port OC-192c module to bay 1, slot 5.
- The boot command boots the module using the image stored in the second (2) location in flash memory.
- The no shutdown command enables the module.
- The show modules command displays the new configuration:
router(config)#module 1/5
router(config-module)#no shutdown
router(config-module)#end
router#show modules
MODULE 1/5:
Server Access Module attached to interface Eth1
Discovered (1xOC192c) 1 Port OC-192c MPLS-Capable
Configured (1xOC192c) 1 Port OC-192c MPLS-Capable
Physical port type is short range single mode fiber
Hardware is 1X0c192c, Version 1.3, Revisions DA
Fabric version is 3.0
Ipriori release version: 5.0.10
Operational image version: Platform: cm-d;Label: R5.0_DEV.89, Built on Mo., Day, Year, Time
ROM Version: Ipriori Bootrom Release 6.8 built Mo., Day, Year, Time
Line Card FPGA Software Version: 0.6
Switch CArd FPGA Software Version: 0.8
POST Software Version: 10.6.0
Product Id: (Rev.); S/N
Module CLEI Code:
Last started on Day, Month, Year Time
Module uptime is 31 minutes, 27 seconds
Administratively Up; Current state is Up
Max number of historical logging files: 5
The Module Command
The module command is used to enter module mode.
Syntax: [no] module bay#/slot# [type]
bay#
Defines the bay number in which this module is located. Default = 1
slot#
Defines the slot number to configure. Slots are numbered from 1 to up to 10 slots depending upon chasis type, beginning at the top left of the machine. Each physical slot is numbered on the hardware for reference.
type
The type of module to configure in this slot. When configuring a 1-Port OC-192c module:
Description: Within module mode, the following commands are available:
The primary function available in module mode is the ability to configure or delete the module that resides in the slot. This is done with the [no] shutdown command. The shutdown command disables and shuts down the module residing in the slot. The no shutdown command enables or configures the module residing in the slot.
Use the no module command to delete a module.
Display the Modules
Use the show modules command to display the current configuration and state for a module.
Syntax: show modules [bay/slot] [brief]
bay/slot
Show only information for the module residing in bay/slot where bay is the bay number and slot is the slot number.
brief
Display summarized information about the specified module(s).
Description: This command displays configuration information for one or all modules residing in this bay.
The show modules brief command will specify which module is the SAM modules by starting the information line with an S in the case of the primary SAM and a B in the case of a backup SAM.
Default: None.
Command Mode: Privileged.
Example 1: In the following example, the show modules command displays information about all the configured modules:
router#show modules
MODULE 1/5:
Server Access Module attached to interface Eth1
Discovered (1xOC192c) 1 Port OC-192c MPLS-Capable
Configured (1xOC192c) 1 Port OC-192c MPLS-Capable
Physical port type is short range single mode fiber
Hardware is 1X0c192c, Version 1.2, Revisions DA
Hardware is 4X0c48c, Version 1.2, Revisions DA
Fabric version is version number
IPriori Release release number
Operational image version: Platform: platform; Label: release label Built on build date, build time ROM Version: IPriori Bootrom Release number.number, build month, day, year
ROM Version: IPriori Bootrom Release number.number, build month, day, year
Line Card #1
Line Card FPGA Software Version: FPGA version number
Line Card #2
Line Card FPGA Software Version: FPGA version number
Switch Card FPGA Software Version: FPGA version number
POST Software Version: version number
Product Id: P4-S16O48-SR-R (Rev. AX); S/N serial number
Module CLEI Code: CLEI code number
Last started on Day Date Time Year
Module uptime is Weeks, Days, Hours, Minutes, Seconds
Administratively Up; Current state is Up
Max number of historical logging files: 5
router#
Fabric version is version number
IPriori Release release number
Operational image version: Platform: platform; Label: release label Built on build date, build time ROM Version: IPriori Bootrom Release number.number, build month, day, year
ROM Version: IPriori Bootrom Release number.number, build month, day, year
Line Card #1
Line Card FPGA Software Version: FPGA version number
Line Card #2
Line Card FPGA Software Version: FPGA version number
Switch Card FPGA Software Version: FPGA version number
POST Software Version: version number
Product Id: P4-S16O48-SR-R (Rev. AX); S/N serial number
Module CLEI Code: CLEI code number
Last started on Day Date Time Year
Module uptime is Weeks, Days, Hours, Minutes, Seconds
Administratively Up; Current state is Up
Max number of historical logging files: 5
router#
The following table describes the fields in the display:
Example 2: In the following example, the show modules brief command displays summarized information about the modules:
router#show module brief
Module Discovered Configured Last Started State
1/1 1xOC192c 1xOC192c MON DEC 17 10:40:07 2003 Up
1/2 2x1GBE 2x1GbE MON SEP 2 10:40:07 2002 Up
.
.
.
1/14 1xOC48c 1xOC48c MON SEP 2 10:40:08 2002 Up
1/15 4xOC3c 4xOC3c MON SEP 2 10:40:07 2002 Up
1/16 1xOC12c 1xOC12c MON SEP 2 10:39:57 2002 Up
1/17 4xOC12c 4xOC12c MON SEP 2 10:40:07 2002 Up
1/18 4xOC12c 4xOC12c MON SEP 2 10:40:08 2002 Up
1/19 4xOC12c 4xOC12c MON SEP 2 10:40:07 2002 Up
router#
The following table describes the fields in the display:
Configuring the Interfaces
Activating a 1-Port OC-192c Interfaces
PROCEDURE: Use the following steps to configure a POS interface:
Step 1 Use the show module command to display configured modules. If the 1-Port OC-192c module is shut down, use the no shutdown command in module configuration mode to activate the module.
Step 2 Use the configure terminal command to enter configuration command mode.
Step 3 Use the interface command pos bay/slot/port location to enter interface configuration command mode.
Step 4 Optionally, modify the default settings.
Step 5 Optionally, configure a description for the interface using the description command.
Step 6 Configure the local address using the ip address command.
Step 7 Use the no shutdown command to activate the interface.
Step 8 Use the show interface command to display and verify the new interface configuration.
The interface Command
The interface command defines/deletes an interface.
Syntax: [no] interface pos bay/slot/port
pos
Configures the interface to support pos.
bay/slot/port
Identifies a specific interface on the TSR. Valid values are as follows:
bay: Bay number. Valid values 1 - 2. Default 1.
slot: Slot number where the module is installed in the TSR. Valid values are integers between 1 and 40.port: Valid values are 1 - 2.
Description: The interface pos command defines a POS interface and enters the interface configuration mode. The interface is not usable as a routing interface until you use the ip address and no shutdown commands.
Configuring a POS Interface
NOTE Be aware that the default for industry-standard routers is to obtain their clock from line. If both ends of the fiber are configured to recover the clock from line, the connection does not work, characterized by SONET failing to come up.
Be sure to include the clock source internal command in your configuration file when configuring the QSR to interoperate with industry-standard routers.PROCEDURE: To configure a POS interface, use the following steps:
Step 1 Use the interface pos bay#/slot#/port# command name the POS interface and enter Interface Configuration command mode.
Step 2 Use the ip address to assign an IP address to the interface.
Step 3 Use the clock source internal command to select the internal clock of the interface for transmissions.
Step 4 Use the no shutdown command to enable the interface.
Step 5 Use the show interface pos bay#/slot#/port# command to display the interface:
router(config)#interface pos 1/5/1
router(config-if)#ip address 5.10.1.2 255.255.0.0
router(config-if)#clock source internal
router(config-if)#no shutdown
router(config-if)#exit
router(config)#show interface pos 1/5/1
POS 1/5/1 is up, line protocol is up
Internet address is 5.10.1.2/16
MTU 10240 bytes,
Payload BW: 9621.504 Mbit/Sec, Total BW: 9953.280 Mbit/Sec
Encapsulation PPP, CRC-32
Loopback: None, Keepalive: Disabled, Scramble: Disabled
LCP: Open, IPCP: Closed, OSICP: Closed MPLSCP: Closed
Received: c
723431054176 bytes
7279943161 directed packets, 0 broadcast packets
0 discards, 0 errors, 0 unknown protocols
Transmitted:
284446377380 bytes
2273151325 directed packets, 0 broadcast packets
0 discards, 0 errors
Medium Type SONET, Line Coding: NRZ, Line Type: ShortSingleMode
Sonet Loopback: None, Sonet Clock Source: Internal
PPP SNMP Trap link-status: enabled
Sonet/Path: SNMP Trap sonet link-status: enabled
TX J0 Section Trace: "1"
RX J0 Section Trace: "0"
Tx Path Trace: "POS 1/12/1 QSR 0"
Rx Path Trace: "NULL"
Displaying the 1 Port OC-192c Interface
Use the show interfaces pos command to display information about the 1 Port OC-192c interface.
Syntax: show interfaces pos bay/slot/port
bay/slot/port
Identifies a specific interface.
Description: Use the show interfaces pos command with no arguments to display information about all the POS interfaces.
Use the show interfaces pos bay/slot/port command to display information about a specific POS interface.
Default: None.
Command Mode: Executive and privileged.
Example 1: In the following example, show interface pos bay/slot/port command displays information about the specified POS interface:
router#show interface pos 1/5/1
POS 1/5/1 is down, line protocol is down
POS 1/15/1 is up, line protocol is down
Internet address is 5.10.1.2/16
MTU 10240 bytes,
Payload BW: 9621.504 Mbit/Sec, Total BW: 9953.280 Mbit/Sec
Encapsulation PPP, CRC-32
Loopback: None, Keepalive: Disabled, Scramble: Disabled
LCP: Open, IPCP: Closed, OSICP: Closed MPLSCP: Closed
Received: c
723431054176 bytes
7279943161 directed packets, 0 broadcast packets
0 discards, 0 errors, 0 unknown protocols
Transmitted:
284446377380 bytes
2273151325 directed packets, 0 broadcast packets
0 discards, 0 errors
Medium Type SONET, Line Coding: NRZ, Line Type: ShortSingleMode
Sonet Loopback: None, Sonet Clock Source: Internal
PPP SNMP Trap link-status: enabled
Sonet/Path: SNMP Trap sonet link-status: enabled
TX J0 Section Trace: "1"
RX J0 Section Trace: "0"
Tx Path Trace: "POS 1/12/1 QSR 0"
Rx Path Trace: "NULL"
The following table describes the fields in the display: