Table A-1. Defaults - Basic Commands
| Command
|
Factory Default
|
| AAA and SSH Commands
|
aaa
|
No AAA services enabled.
|
aaa accounting
|
Disabled.
|
aaa last-resort
|
Disabled.
|
aaa optional-passwords
|
Last-resort authentication uses the system password.
|
aaa password-prompt
|
None
|
aaa policy
|
Select the first available AAA server.
|
aaa protocol
|
TACACS+.
|
aaa retransmit
|
3.
|
aaa source-interface
|
The source interface is the ethernet 0 interface.
|
aaa tacacs directed-request
|
Disabled.
|
aaa tacacs host
|
None.
|
aaa tacacs key
|
No key configured.
|
aaa tacacs port
|
Port 49.
|
aaa tacacs priority
|
If no primary server is configured, all servers in the server list default to secondary using a first-available policy.
|
aaa timeout
|
5 seconds.
|
aaa username-prompt
|
None
|
disconnect ssh
|
None.
|
disconnect telnet
|
None.
|
ip ftp
|
Enabled.
|
ip ssh
|
Disabled.
|
ip ssh permit
|
Disabled.
|
ip ssh version
|
compatibility mode.
|
ip telnet
|
Enabled.
|
show aaa
|
None.
|
show ip ssh
|
None.
|
| ATM Commands
|
clock source
|
line.
|
atm ilmi-keepalive
|
The factory defaults are shown below:
|
atm maxvc
|
200.
|
atm uni-version
|
4.0
|
default
|
None.
|
description
|
None.
|
ilmi-enable
|
Disabled.
|
ilmi manage
|
Disabled.
|
ip address
|
None
|
mtu
|
MTU 4470.
|
oam-pvc manage
|
Disabled.
|
oam retry
|
|
protocol ip
|
None.
|
pvc
|
None.
|
show atm pvc
|
N/A.
|
show interface atm
|
N/A
|
| Central Office Alarm Commands
|
service led-test
|
N/A
|
show co-alarms
|
N/A
|
silence co-alarms
|
N/A
|
| Configuration and File Management Commands
|
boot
|
None.
|
cd
|
None.
|
configure
|
None.
|
copy
|
None.
|
delete
|
None.
|
dir
|
None.
|
erase
|
None.
|
failover
|
None.
|
more
|
None.
|
post-burn
|
None.
|
pwd
|
None.
|
reboot
|
None.
|
reload
|
None.
|
rom-burn
|
None.
|
show boot
|
None.
|
show flash
|
None.
|
show reload
|
None.
|
show running-config
|
None.
|
show startup-config
|
None.
|
squeeze
|
None.
|
tail
|
Display the last 10 lines.
|
undelete
|
None.
|
unerase
|
None.
|
upgrade all
|
None.
|
write
|
None.
|
| Fabric Commands
|
fabric link down-event
|
10.
|
fabric link heuristic shutdown
|
Enabled
|
fabric link time-window
|
10 minutes.
|
fabric-version
|
Fabric version 2.0.
|
show fabric channels
|
None.
|
show fabric counters
|
None.
|
show fabric links
|
None.
|
show fabric paths from module
|
None.
|
show fabric scrubbing-counters
|
None.
|
show fabric version
|
None.
|
shutdown fabric link
|
Enabled.
|
| General Commands
|
alias
|
None.
|
disable
|
None.
|
do
|
None.
|
enable
|
None.
|
end
|
None.
|
exec-timeout
|
10 minutes.
|
exit
|
None.
|
help
|
None.
|
history
|
Enabled.
|
history size
|
10 lines.
|
ip netmask-format
|
Decimal format.
|
length
|
24 lines.
|
line
|
None.
|
line vty session-limit
|
15
|
login
|
Disabled.
|
logout
|
None.
|
password
|
The password defined by the system-password command.
|
privilege level
|
0 (executive command mode).
|
quit
|
None.
|
rlogin
|
None.
|
run
|
None.
|
show alias
|
None.
|
show history
|
None.
|
show line
|
None.
|
show terminal
|
None.
|
telnet
|
None.
|
width
|
80 characters per line
|
| Interface Commands
|
arp
|
For encapsulation type: ARPA.
|
clear arp-cache
|
None.
|
clear counters
|
None.
|
close-threshold
|
0. Close composite link when the last member link closes.
|
crc
|
32.
|
default crc
|
32.
|
default keepalive
|
10 seconds.
|
default mtu
|
4470 bytes.
|
description
|
No description defined.
|
encapsulation
|
PPP encapsulation.
|
flowcontrol
|
Symmetric.
|
interface
|
None.
|
ip access-group
|
No default access group defined. The default direction for filtering packets is outbound.
|
ip accounting mac-address
|
Disabled.
|
ip address
|
No IP address defined.
|
ipcp-negotiation
|
Enabled.
|
keepalive
|
10 seconds.
|
lacp
|
Enabled on configuration of aggregate link.
|
mac address
|
Lowest configured module port for this aggregate link.
|
marker
|
Disabled.
|
member-link gbe
|
No aggregate links or member-links defined.
|
member-link pos
|
No composite links or member-links defined.
|
mirror
|
None
|
monitor
|
None.
|
mtu
|
4470 bytes.
|
mtu-negotiate
|
Negotiation Enabled.
|
negotiation auto
|
Negotiation disabled.
|
open-threshold
|
0.
|
peer default ip address
|
No default address defined.
|
ppp negotiation-timeout
|
30 seconds.
|
remote-fault-indication
|
Enabled.
|
show interface aggregate-link
|
None.
|
show interface composite-link
|
None.
|
show interface ethernet
|
None.
|
show interface gbe
|
None.
|
show interface loopback
|
None.
|
show interfaces mac-accounting
|
None.
|
show interface pos
|
None.
|
show interface statistics
|
None.
|
show interface vlan
|
None.
|
show ip arp
|
None.
|
show output-interface
|
N/A.
|
show smon control
|
None.
|
| Logging Commands
|
clear logging
|
None.
|
clear obituary
|
N/A.
|
copy logging
|
None.
|
include
|
No logfiles configured.
|
logging
|
Logging is not sent to a remote host.
|
logging destination-port
|
UDP Port 514.
|
logging-file
|
N/A
|
logging-filter
|
Warning messages and above logged for all systems, with the exception of user-commands where the default is informational and above.
|
logging-filter high-availability
|
Warning messages and above logged for all sub-systems, with the exception of user-commands where the default is informational and above.
|
logging-max-history
|
Up to five files stored.
|
max-files
|
5 log files
|
logging monitor
|
Logging messages are not sent to the console, telnet, or SSH session.
|
logging source-interface
|
Ethernet 0.
|
logging source-port
|
UDP Port 514.
|
logmsg
|
None.
|
show
|
None.
|
show logging
|
None.
|
show obituary
|
None.
|
size
|
128 KB
|
snmp-server trap-source
|
loopback 0.
|
| NTP Commands
|
ntp master
|
N/A
|
ntp peer
|
N/A.
|
ntp server
|
None.
|
ntp access-group
|
None
|
ntp update-calendar
|
Enabled - System calendar updated by NTP.
|
ntp source
|
Source address is reported as an outgoing interface address.
|
show ntp associations
|
N/A
|
show ntp counters
|
N/A
|
show ntp status
|
N/A
|
| Protocol Debug Commands
|
debug all
|
Disabled.
|
debug ip bgp
|
Default value for interface is none (enable debugging on all interfaces). Default value for level is terse.
|
debug ip icmp
|
Default value for interface is none (enable debugging on all interfaces). Default value for level is terse.
|
debug ip ospf
|
Default value for interface is none (enable debugging on all interfaces). Default value for level is terse. OSPF NBR States, OSPF Interface Types, OSPF Interface Events, OSPF Interface States
|
debug isis
|
Default value for interface is none (enable debugging on all interfaces). Default value for level is normal.
|
debug mpls ldp messages
|
Default value for interface is none (enable debugging on all interfaces). Default value for subsystem is "ldp". Default value for level is terse.
|
debug mpls ldp msg-hex-dump
|
Default value for interface is none (enable debugging on all interfaces). Default value for level is normal.
|
debug ppp
|
Default value for interface is none (enable debugging on all interfaces). Default value for subsystem is both LCP and IPCP. Default value for level is terse.
|
debug mpls rsvp
|
Default value for interface is none (enable debugging on all interfaces). Default value for level is terse.
|
debug mpls ldp sess-fsm
|
Default value for level is normal.
|
logging log-debug
|
None.
|
show debugging
|
None.
|
| Remote Monitor Commands
|
rmon alarm
|
None.
|
rmon event
|
None.
|
rmon enable
|
Enabled.
|
rmon log size
|
200 per event.
|
show rmon alarms
|
None.
|
show rmon enable
|
None.
|
show rmon events
|
None.
|
show rmon log
|
All entries.
|
show rmon value
|
None.
|
| SNMP Commands
|
debug snmp headers
|
None.
|
debug snmp dump-packets
|
None.
|
show snmp
|
None.
|
show snmp hosts
|
None.
|
snmp-server community
|
For access: read-only (ro). For access list: all IP addresses.
|
snmp-server contact
|
None.
|
snmp-server enable traps
|
SONET failure traps and failure clear traps are enabled.
|
snmp-server group
|
No groups defined.
|
snmp-server host
|
For community-name: SNMP_trap. For SNMP version: Version 1. For trap-category: All eight categories allowed.
|
snmp-server location
|
None.
|
snmp-server trap-source
|
loopback 0.
|
snmp-server engineid
|
None.
|
snmp-server view
|
vldefault
|
snmp-server user
|
No users defined.
|
snmp trap link-status
|
Link-status trap enabled.
|
snmp trap sonet line
|
Failure traps and failure clear traps are reported. All other SONET line traps are disabled.
|
snmp trap sonet line-far-end
|
Failure traps and failure clear traps are reported. All other SONET far-end-line traps are disabled.
|
snmp trap sonet link-status
|
SONET link-status trap enabled.
|
snmp trap sonet path
|
Failure traps and failure clear traps are reported. All other SONET path traps are disabled.
|
snmp trap sonet path-far-end
|
Failure traps and failure clear traps are reported. All other SONET path-far-end traps are disabled.
|
snmp trap sonet section
|
Failure traps and failure clear traps are reported. All other SONET section traps are disabled.
|
| SONET/SDH Commands
|
clear sonet performance current
|
None.
|
clock source
|
Line.
|
loopback
|
No loopback configured.
|
show sonet performance
|
None.
|
show sonet status
|
None.
|
show sonet thresholds pos
|
None.
|
shutdown
|
Interface is shutdown.
|
sonet failure-delay
|
2500ms.
|
sonet flag
|
For the c2 byte: 22. For j0 with framing set to SONET: 1. For jo with framing set to SDH: None.
|
sonet framing
|
SONET framing.
|
sonet path-trace
|
host-name/Interface-type/bay/slot/port/Line-rate
|
sonet scramble-atm
|
Scrambling is enabled.
|
sonet threshold
|
1 (all thresholds).
|
sonet threshold line
|
1 (all thresholds).
|
sonet threshold line-far-end
|
1 (all thresholds).
|
sonet threshold path
|
1 (all thresholds).
|
sonet threshold path-far-end
|
1 (all thresholds).
|
sonet threshold section
|
1 (all thresholds).
|
| SONET APS
|
aps authenticate
|
No authentication string configured.
|
aps force
|
None.
|
aps group
|
No group name configured.
|
aps lockout
|
Disabled.
|
aps manual
|
None.
|
aps protect
|
APS mode not configured.
|
aps timers
|
Keepalive-time = 1 Second. Holddown-time = three times the keepalive-time.
|
aps working
|
APS mode not configured.
|
show aps
|
None.
|
| System Administration Commands
|
arp retry count
|
3 retries.
|
arp retry timeout
|
5 seconds.
|
arp timeout
|
1200 seconds.
|
auto-upgrade
|
Auto-upgrade enabled, globally and on the modules.
|
banner
|
No banner display.
|
bay
|
bay-all
|
checkpoint
|
None.
|
clear counters
|
None.
|
clear counters ttl-expiry-counters
|
N/A.
|
clear reliability counters
|
None.
|
clock set
|
Set to EST at the factory.
|
clock timezone
|
Null string.
|
crashdump
|
Disabled.
|
crashdump force
|
Disabled.
|
crashdump restrict
|
Enabled.
|
debug show tech-support
|
default failover window Duration = 30 minutes, Threshold = 3 failovers.
|
enable password
|
avici (in clear text mode)
|
failover
|
None.
|
failover window
|
Duration = 30 minutes, Threshold = 3 failovers.
|
fpga activebank
|
None.
|
fpga download
|
None.
|
hostname
|
Host name is router.
|
mode
|
Warm.
|
module
|
module all
|
package-file
|
No default package file defined.
|
ping
|
None.
|
rlogin
|
None.
|
primary-preference
|
20.
|
redundancy
|
None.
|
reliability period
|
12 hours.
|
sam-timeout-multiplier
|
Multiplier = 1.
|
sam-aes-threshold
|
Threshold = 3.
|
send
|
None.
|
server
|
None.
|
server-id
|
No server-id configured.
|
server-location
|
None.
|
server threshold
|
N/A
|
show banner
|
None
|
show bay
|
None.
|
show bay slots
|
None.
|
show calendar
|
None.
|
show clock
|
None.
|
show cpu
|
None.
|
show crashdump
|
None.
|
show fpga module
|
None.
|
show memory
|
None.
|
show modules
|
None.
|
show modules ttl-expiry-counters
|
N/A.
|
show modules ttl-expiry-counters
|
N/A.
|
show package-file
|
None.
|
show population
|
None.
|
show redundancy
|
brief.
|
show server verbose
|
None.
|
show sntp
|
None.
|
show users
|
None.
|
show usernames
|
None.
|
show version
|
None.
|
sntp server
|
No SNTP server defined.
|
system-password
|
avici
|
upgrade
|
None.
|
username
|
None.
|
warm-standby
|
Enabled.
|
